What would be a good cam for a chevy 355? and should i put 64cc heads on it?
The 355 is going to be put in a mud truck. Its not built to race just play.
You might want to check out the Crane PowerMax cam. This is the cam Crane suggested for my overhaul a few back w/ the Performer hi-rise intake. That I work on for my 91 Silverado Z71 w/ the ECM corrected. If, you can dealin w/ a couputer on the vehicle then the door opens bigger for you suggestion of cam up-grades.
I'd suggest callin one of the cam manufacture and decussing you needs and intentions over w/ them and let they help you deside on the right cam for you application.
Good luck!
powered by Yahoo Answers
Incoming search terms for the article:
- ITS GOTTA THREE QUARTER CAM
- will 64cc sbc heads make more power
- sbc truck cam
- SBC Race Cam Specs
- sbc mud truck cam
- sbc compression ratio with 64cc
- SBC cam size
- sbc 355 with 64cc heads compression ratio
- SBC 355 camshaft help
- recomended camshaft for 355 chevy
3 Responses to “What would be a good cam for a chevy 355? and should i put 64cc heads on it?”
Leave a Reply
|
the cam and other devices are intended to increase volumetric effeciencey.. you can never get a cylinder to fill one hundreds percent.. but the more radical the cam the worst the enging performs when ideling or trying to go slow.. i would recommen a two speed rear that you can shift with the transmission.. with a full race cam you cant drive on the streeet.. so i recommen a modified three quarter cam.. and agin if you get this you have to have it case hardened.. with high rpm it will wipe out the lobes. quickly ok gilermo.
References :
3/4 cam? I don't think a chevy cam with 4 lobes cut off of it will work too good.. Which end you gonna cut off the rear that has the gear or the front where timing chain goes?
Sorry to rag on you man, but this aint the 50's anymore.. There's over 2,000 diff cam profiles for the chevy small block… What's a full race cam and whats a 3/4?
64cc heads will bump up the compression on engine if it has 70, 72, 74, 76 cc heads.. You'll gain power from the compression.
The cam and compression ratio needs to match each other close or you'll have an engine that's lazy on the low rpm side, or an engine that pings it's self to death.
With stock type heads, you will make more power by using a dual pattern cam (one with more exhaust duration and lift than intake) In most cases 8-12 degrees more duration on exhaust side works best.
With out know more specs, I can't/won't recommend a cam size though.. I need to know compression ratio.. If you don't know it and engine is stock you can give me the casting # and sufix code and I can look it up, them figure out compression with 64cc heads and recommernd a cam
References :
Performance/Race engine builder, 12+ years
You might want to check out the Crane PowerMax cam. This is the cam Crane suggested for my overhaul a few back w/ the Performer hi-rise intake. That I work on for my 91 Silverado Z71 w/ the ECM corrected. If, you can dealin w/ a couputer on the vehicle then the door opens bigger for you suggestion of cam up-grades.
I'd suggest callin one of the cam manufacture and decussing you needs and intentions over w/ them and let they help you deside on the right cam for you application.
Good luck!
References :
<http://www.thirdgen.org/mods3 >
<http://www.cranecams.com/index.php?show=browseParts&action=partSpec&partNumber=114122&lvl=2&prt=5 >
<http://www.cranecams.com/?show=browseParts&lvl=3&prt=122&action=partSpec&partNumber=99848 >